Aqualis Caleo high-temperature air-to-water heat pumps are specially .. As part of its policy of continual product improvement, CIAT reserves the right to make. AQUACIAT CALEO: the refurbishment solution suitable for both large homes and as those offered by CIAT´s Aqualis Caleo product – were limited to 20kw. Consult CIAT’s NAN brochure on MedicalExpo. Aqualis 2’s added benefits The Aqualis 2 heat pump from CIAT is the key AGEO CALEO – NAD.
|Published (Last):||6 April 2011|
|PDF File Size:||18.70 Mb|
|ePub File Size:||19.11 Mb|
|Price:||Free* [*Free Regsitration Required]|
Check the glycol content if used. English Installation D e u t s ch – Settings stored in memory for two hours following a power cut – Blue backlit digital display – Maximum dimensions: Failure to comply with the requirements of the above standards will void the CIAT warranty. As the hoses are insulated, bend them at sufficiently wide angles to avoid pinching the inner tube and restricting the flow of water.
Fault management remains on during test mode. xqualis
AQUALIS CALEO |
The Online Industrial Exhibition. The diameters of the tubes are not necessarily the same as those of the unit. This packaged unit is designed to be installed outdoors in urban environments. Particularly suited to renovations, the unit is designed to be connected to an optional mixing tank with multiple connections that supplies cait to high-temperature radiators.
It is essential that they be fitted if the unit is installed on anti-vibration mounts. Protect from prevailing winds. For your own comfort, avoid locating the equipment too close to sensitive areas such as bedroom windows. Turned off in the following three cases: Its compact footprint makes it particularly suited for installation as a boiler backup on existing systems.
Please contact your boiler manufacturer to find out whether the heating source is compatible with Microconnect control.
Quiet variable speed propeller fan driven by an electronically commutated DC brushless motor. It is therefore strictly prohibited to bypass it; doing so will create a safety hazard to property and people.
Serves as a boiler backup in large homes and multi-residential buildings as well as businesses, hotels and healthcare facilities. Boiler operation authorised symbol Application: If you do calro have a torque wrench, tighten them until they are snug then tighten a further three-quarters of a turn. Always comply with applicable standards and regulations. New generation hermetic scroll compressor with partial vapour injection and RC refrigerant. Connect the kit and filter to the return water line.
The room temperature is managed by aqualks Microconnect terminal. Then attach the mounting plate to a wall using the screws and anchor bolts or a flush-mount box 60 mm centre distance using the holes Fig.
Italiano 3- Using litmus paper aquallis a pH meter, check the pH obtained.
In hot water production mode heating, pool, frost protection or domestic hot water modes: This can be done by opening the manual bleed valve located under the unit cover when turning the unit on or by installing a section of the water line and an automatic bleed valve over the unit.
English The differential water aquaalis switch is a safety component. Although it is rain resistant, it may be installed under a shelter with adequate ventilation on all four sides.
Faults are stored in memory during power cuts and the fault relay is stuck in a particular position.
New generation hermetic scroll compressor with partial vapour injection and RC refrigerant. Check for any water or oil leaks around the unit and make sure the condensate water drains correctly.
If the direction of rotation is wrong: Electrolyte couplings may be obtained from specialist distributors in the case of major corrosion problems. Remove the top as shown in Figure 1 and make a connection to terminal block J1 on the PSU board the one with the contactor. English To protect your heating system and avoid all risks of it freezing should it be intentionally or accidentally turned off, we strongly advise that you: Mounting First detach the terminal from its mounting plate, as shown in Fig.
The control setpoint is displayed in all other cases. Terminal display when the outdoor temperature is less than P9 and only the boiler is authorised. Adjusting setting P6 P6 Auxiliary configuration Bypass type by opening of contact on terminal block J2 – terminals 4 and 5 0 No auxiliary units Heat pump turned off 1 Electric auxiliary units Only electric auxiliary units turned off 2 Electric auxiliary units Heat pump and electric aqulis units turned off 3 Boiler auxiliary Heat pump turned off and boiler turned on e.
NF C in France and are under the responsibility of the installer. Medium capacity air-to-water heat pump for “high temperature” heating only. Using a corrosion inhibitor will also prevent the formation of sludge caused primarily by corrosion.
The protective covers may be removed in order to change the circulator speed or reach the release screws. The valve does not need to be separated from the heater by a shut-off valve. With the thought of material improvement always in mind, CIAT reserves the right, without notice, to proceed with any technical modification. If ciatt system is fitted with an optional calfo heater, install the valve near it. Hoses must be used to connect the water pipes to limit as far as possible the vibrations transmitted to the building.
Its compact footprint makes it particularly suited for installation as a boiler backup on existing systems. Serves as a boiler backup in large homes and multi-residential buildings as well as businesses, hotels and healthcare facilities. Never add them separately.
No special precautions are required to protect it from adverse weather other than frost in areas where frost is a possibility.